Saturday, October 1, 2016

Global Potential of Energy from Biomass and its formulation

World largest power plant employing Biomass is Drax, UK, which has installed capacity of 3960 MW with 1320 MW from Biomass.
Drax generates 8 TWh energy from Biomass Per year.
which is tantamount to 22 GWh/day.

The potential calculation for Biomass:
Average irradiation on earth= 1500 kWh/m^2/year
=171 W/m^2
Photosynthetic efficiency is quite low= 0.4% only
So, Power density of tree= 171*0.4%= 0.68 W/m^2
Thermal conversion efficiency= 25%= 0.68*25%= 0.171 W/m^2
Energy density= 0.171*24*365/1000= 1.5 kWh/ year/m^2

The overall efficiency comes out to be only 0.1%.

Products:
Biofuels= Ethanol, extensively used in brazil
Biogas= Methane, Methane is a green-house gas (GHG). The global warming potential of methane is 72 times higher than global warming potential of CO2 for the period of 20 years. Methane contributes 7-9% to global warming.

Note: Algae has higher photosynthetic efficiency than crops so better for biomass energy conversion.
The average carbon footprint of Biomass plant is 230 gCO2/ kWh, much higher than other renewables but much lower than the coal-fired power plant.

Global capacity= 93 GW
                          = 433 TWh/ year
                          =1.9% of global energy demand
                          = 7.6% of all renewables
Besides electricity, more energy is in the form of thermal energy,
Global thermal capacity= 305 GW
                                       = 2300 TWh/ year
                                      = 12500 TWh/ year including cooking, heating, transportation
All Biomass in combine accounts for 12 % of the global energy use and 63% of the renewable energy shares.
= 1.69 kWh/person/day
= 0.58 Human Unit
                                      

Saturday, September 24, 2016

Some facts about Solar Energy

Solar Energy is:

  • Scalable
  • Cheap and Predictable
  • Low Capacity factor= 10-20% only
  • Lifetime is quite good- 20-30 years.
  • Carbon footprint is more than Wind energy- 48 gCo2/kWh
  • Global installed capacity is 227 GW
  • Global Energy Production is 235 TWh, i.e 0.08 kWh/Person/day
  • Solar energy serves about 1.2% of the global energy demand
  • Solar energy accounts for 4% of the renewable energy produced throughout the world.

Friday, September 23, 2016

Something to know about Wind Energy

Only 59.3% of the energy of the wind can be converted into mechanical energy. The Commercially available wind turbine has about 40-50% of the wind energy into mechanical energy. Average Co2 footprint for Wind energy is 11 gCO2/kWh for onshore farm and 12 gCo2/kWh for the offshore farm.

Today the wind energy share 2.3% of the global energy demand and this is about 10% of the all renewable energy produced in this world. This data is tantamount to 0.19 kWh/person/day= 0.07 Human unit/person/day

Denmark has developed good amount of wind energy. The wind installed capacity in denmark is about 5 GW and the annual energy production is 14.13 TWh.  Looking at the kWh/W, its only 2.8 kWh/W. The capacity factor comes out to (2.8/(365*24/1000) 0.32 only. In comparison with the capacity factor of hydro electricity 0.7, it can be concluded that the wind energy produces less electricity per installed capacity than hydro electricity. The amount of energy produced from wind turbine depends on the wind speed. The wind speed is dependent on daily and seasonal wind profile, terrain, and the height at which we extract energy from wind.

Power from wind turbine
E= 1/2 mv^2
m=density* volume
=ρ*A*v*t
E/t= 1/2*ρ*A*v*v^2
P=(1/2) ρ*A*v^3

The power produced from wind turbine is proportionla to cube of wind velocity. 

A turbine with rated power 1.5 MW is the power that can be produced by wind turbine at rated speed. The efficiency of turbine drastically reduces at low speed as well as high speed apart from the rated speed.

Wednesday, September 21, 2016

Key Points to be remembered about Hydro Electricity

Typically, the carbon footprint of hydroelectricity is only 24 gCo2/KWh whereas the carbon footprint of Coal fired power plant is much larger, 820 gCO2/KWh.

In 2015, hydroelectricity was only 16.6 % of the global energy demands. for 7.4 billion people living in this world, this energy is equivalent to 1.47 KWh/person/day which is tantamount to 0.5 human unit only. The share of hydroelectricity is considered to rise up to 25% of the global energy share.

Energy density calculation in hydropower design
Suppose, in a suitable land for hydropower development has the rain gauge reading of 500 mm/ year.
Rain= 500 mm/year
Rain= 0.5m^3/m^2/ year= 0.5*1000*10
= 500 kg/m^2/year

Potential energy of water Epot= mgh
=500*9.8*100 (h=100)
=490n Kj
Epot= 490*9.8*100
=0.14 KWh/m^2

Including losses, evaporation, and leakage, only 20% energy from hydropower dam is used for voting.

Use of Energy by sector

Transportation= 25% of the global energy use.

Residence and Buildings= 20% of global energy use

Industrial Sector= 54% of the total energy used.

Rest of the sector share only 1% energy.

Transportation= fuel or battery or direct supply for Car, Bus, Train, aeroplane sector
Residential= Heating, Cooling, Refrigeration, Air conditioning, Cooking, lighting etc.
Industrial= Iron and steel industry, Aluminium industry, wood industry, food industry, chemical industry, irrigation projects, drinking water projects, fine products etc.

Sunday, September 18, 2016

Measurement of Energy

16 watt Lamp if used for 24 hours continuously consumes only 0.13 Human Unit of energy where as the energy produced by 500 MW coal fired power plant is equivalent to energy required for being live for 4.1 million people.

Wednesday, February 18, 2015

Corona, its Effects and its Prevention

Corona is a form of Partial discharge which is luminous and occasionally visible to the Naked Eye.

Corona are caused when the air around an energized conductor gets ionized, causing a discharge. Corona are caused when defects are present in the conductors such as jagged edges or cracks which cause high local electric field. A hissing sound can also be heard during the occurrence of Corona.

The Nitrogen molecules in the air get excited and result and cause ultraviolet radiation. Corona is sometimes visible as a hazy blue light around conductors, especially during the night.

The Effects of Corona

1. Corona is accompanied by the creation of ozone and nitrogen oxides. Nitrogen oxides may react with moisture in the air and form nitric acid a potentially corrosive substance.
2. Corona can cause damage to insulators used in High voltage applications.
3. Corona emissions are accompanied by the generation of radio waves which can interfere with commercial radio transmission. Sometimes, Corona can also result in noise which may disturb the neighborhood.
4. It can sometimes cause carbon deposits which may later result in arcing.

Controlled discharging of Inductive HV Equipment

High Voltage equipments need to be discharged prior to any maintenance work.  The discharge is usually done with an earthing rod after verifying that there is no voltage present on them with an non-contact voltage detector.

In the case of inductive equipment such as transformers and motors with high inductance value in their windings, a controlled discharge needs to be carried out.  Inductive components such as windings in transformers and motors have high inductance.  Sudden discharge of these windings will create a high discharge current and a rapid change in the flux which will result in a high voltage pulse (according to Lenz' Law). This can damage the winding insulation.

The controlled discharge is carried out with a discharge rod with a resistor in series.  The resistor used is a special non linear resistor which has a reverse temperature coefficient which means that as the temperature increases the resistance falls.  When the discharge is started, the resistance is high. As current flows through the resistor, the temperature of the resistor rises and its resistance falls.  Thus the current flow is increased.

The resistor ensures that the discharge is gradual.

what is prospective short circuit current?

Prospective Short Circuit Current refers to the maximum short circuit current which can flow in a circuit in the event of a fault such as a short circuit or an earth fault.  It is the maximum current which can flow in the system.  

All the components of the system such as the cables, bus bars and the measuring and protection systems should be rated with reference to the Prospective Short circuit current. The interrupting devices such as fuses and circuit breakers should have an interrupting capacity greater than the prospective short circuit current.   
Prospective Short Circuit Current depends on the resistances and reactances of the system.  The prospective Short Circuit Current can  be obtained by a Fault Level Calculation Study of the system.

Tuesday, February 3, 2015

Difference between salient pole and non-salient pole rotor used in synchronous generator.

synchronous machine can be characterized by the type of rotor used. Rotors used in Synchronous alternators can be classified into:
1)Salient and
2)Non-Salient Pole Rotors or cylindrical rotors
Salient pole rotors are used in application with speeds from 100 to 1500rpm. They are alternative known as "projected pole" type of rotors. The poles mounted on the rotor are made of lamination's made of steel. The poles are connected to the rotor shaft by means of dovetail joints. Each pole has a pole shoe around which the winding is wound. The salient pole rotor is generally used in applications where the prime mover is a hydel turbine or a combustion engine which have low or medium speeds. Salient pole rotors usually contain damper windings to prevent rotor oscillations during operation. Due to low speed, they are constructed with higher no. of pole (ranging from 8-24 or higher) to achieve system frequency so they can be said as higher pole machine. Almost all hydro power uses salient pole rotor synchronous generator.
                               Non-salient pole rotors are generally used in application which operate at higher speeds, 1500rpm and above. The prime movers in these applications are generally gas or steam turbines. These are sometimes known as "drum rotors". The rotor is a cylinder made of solid forged steel. The slots on which the windings are fixed are milled on the rotor. The number of poles is usually 2 or 4 in number. Since these rotors are cylindrical, the windage loss is reduced. The noise produced is also less. These rotors have higher axial length. These rotors do not need damper windings. Due to high speed, they are used with gas turbine and high speed steam turbine in nuclear power plant and thermal power plant.